Control Equipment
The MP15 panel is an automatic start-up panel for the generating set in the event of a mains failure.
The MP15 automatic panel is the standard equipment with the most functionalities in the market and it is easy to use, even by untrained personnel. It comes in different versions, depending on the customer requirements.
The design conditions include operating at extreme environmental temperatures, IP65 protection and great resistance to electrical disturbances such as overvoltage caused by atmospheric discharges. Therefore, it is a very reliable and robust panel.
Equipment with great processing power
A 10.1” colour display shows:
- Generating set operating status.
- Electrical measurements.
- Preventive alarms and shutdown alarms.
- Events log.
- Harmonics analysis.
Touch buttons are used to browse between displays, so there is no mechanical contact and a high level of operating security is offered.
Generating set control equipment
Our control equipment includes different functionalities.
- MP15-E Generating sets for mains failure
- MP15-E5 Generating sets for mains failure with no break load transfer
- MP15-DR Remote signal started generating sets
- MP15-DR5 Remote signal started generating sets with no break load transfer
- MP15-SCR Generating sets in parallel
- MP15-SCR5 Generating sets in parallel with no break load transfer
The MP15-E panel is an auto-start control panel for the generating set on mains failure situations. It controls the mains supply, automatically starting up and shutting down the generating set, marshalling the switching process and controlling the smooth running of the set at all times.
The MP15-E5 panel makes it possible to carry out no break load transfers (i.e., without going through zero) not only from generating set to mains when mains resumes supply, but also from mains to generating set by automatic synchronisation and load transfer on ramp. This enables the user to test the generating set with the real load at any time, without the installations being affected by the supply being cut off.
The MP15-E5 equipment complies with the technical conditions established in the Spanish Low Voltage Electrotechnical Regulation ITC-BT-40 4.2 concerning no break load transfer. It can be set up for switching by means of motorised automatic circuit breakers or switching via contactors.
The MP15-DR panel is an auto-start control panel for a generating set that is activated by an external signal. This start signal normally comes from switch control equipment of the CON-2015 type (or similar) that controls the mains supply and gives the start signal to the generating set in the event of a mains failure.
While the generating set is operating, the panel controls the smooth running of the set.
The MP15-DR5 panel is an auto-start control panel for a generating set when it receives an external signal. This external signal comes from switch control equipment of the CON-5015 type, which gives the start signal when there is a mains failure.
The combination of these two control equipments makes possible to carry out no break load transfers, not only from generating set to mains when the mains resumes supply, but also from mains to generating set by load transfer on ramp.
The MP15-SCR panel is an auto-start and automatic synchronisation control panel for the generating set for working in parallel with other sets on receiving a start-up signal. This start-up signal normally comes from switching control equipment of the CON-2015 type (or similar) that controls the mains and gives that start-up signal to the generating sets when a mains failure occurs.
It controls the loads sharing on the basis of the capacity of each set.
Each set in parallel is equipped with a MP15-SCR panel containing all the MP15 panel functionalities, in order to control each one of the generating sets, as well as to provide overall supervision for all the sets in parallel.
Communication between the MP15-SCR panels of the generating sets makes an additional synchronism panel unnecessary.
The MP15-SCR5 panel is an auto-start and automatic synchronisation control panel for the generating set for working in parallel with other sets on receiving a start-up signal. This external signal comes from switching control equipment of the CON-2015 type that gives that start-up signal to the generating sets when a mains failure occurs. It controls the loads sharing on the basis of the capacity of each set.
It can also carry out no break load transfers (i.e., without going through zero) not only from generating sets to mains when mains resumes supply, but also from mains to generating sets by automatic synchronisation and load transfer on ramp.
Each set in parallel is equipped with a MP15-SCR5 panel containing all the MP15 panel functionalities, in order to control each one of the generating sets, as well as to provide overall supervision for all the sets in parallel.
Would you like further information? Get in touch with us